ElaSticone GSX is an invisible protective treatment formulated to protect masonry and stone surfaces from water, oil, graffiti and more. This product is designed for high-performance building restoration and preservation applications.
This product is based on an inorganic skeletal framework that when combined with a fluoropolymer creates a clear, penetrating barrier that will protect surfaces against oil and water stains, graffiti and more without altering the surface appearance of the stone. It is designed to penetrate the surface and react with the silica within the stone, expanding and filling cracks and crevices in the material to create a long-lasting repellency to water and dirt. This treatment will help to deter unsightly stains caused by mold and mildew. Surfaces treated with this product can be easily cleaned using a mild detergent such as Presto’s Green-Kleen®.
ElaSticone GSX can be used on either horizontal or vertical surfaces. Horizontal surfaces may need reapplication sooner than vertical surfaces.
Complete all caulking and surrounding construction substrate applications prior to use of this product. Newly installed stone or grout must be allowed to cure before application. Protect against personal contact with this and all chemical products.
Use protective gear to prevent personal contact. Use a lowpressure sprayer, roller, brush, sponge or lambs wool applicator. Product may also be back rolled. Do not dilute; apply full strength. Never apply to a damp or wet surface. Do not apply at below freezing temperatures. Protect any unintended areas. Apply product to create an even coat on the surface. Allow product to saturate surface. Do not allow product to pool on the surface and dry, or protection will be uneven and a residue may form. Remove any excess material by use of a rag or towel.
A second coat may be needed for porous, absorbent surfaces or for superior protection. Subsequent coats should be applied in the same manner as the first while the initial application is drying. Never apply a second coat if two coats were not tested and approved prior to use. Protection will begin immediately after sealant dries on the surface. Cure time for maximum water and stain protection is 24-72 hours.
Protect surface from contact with water for at least 48 hours. Application rates, concentration, temperature and humidity can impact dry and cure time. Use towels or rags to polish the surface and remove any excess product.
In many instances, a combination of different stone cleaning products is necessary for various stone surfaces depending on their level and type of staining. Presto offers a complete line of stone cleaning products for all situations, including:
Clean tools and equipment with mineral spirits. In the event ElaSticone GSX is allowed to come in contact with adjacent surfaces, dries and is difficult to remove, use any of the following surface restoration products:
For ongoing maintenance of the protected surface, we recommend the use of Green-Kleen diluted 10 to 1 with water, preferably heated deionized water. Apply the diluted product to the surface. Allow to sit for one or two minutes and scrub with a soft bristle if necessary to remove build up. Then gently rinse the surface clean with low pressure. For exterior vertical surfaces, we recommend cleaning the surface every 2-3 years in order to retain a clean appearance and preserve the previous restoration. High pressure is not needed and may damage the surface coating or weaken its performance. This maintenance cleaning is not mandatory to ensure the coating will last as stated in the warranty and is only a recommendation.
The information provided by Presto for the safe and effective use of this product, and all of our products, is believed to be good and accurate. However, due to the many different possible applications of this product, careful considerations should be made when selecting its suitability for each surface.
The information provided should never be substituted for individual testing to ensure the product’s compatibility with each surface intended for use. The purchaser shall assume all responsibility for determining the suitability of this product. When used as intended, this product will perform as stated. No other warranty can be made for this product, verbally or written.
Presto warrants this product to be free from defects. In the event this product is found to be defective, we will provide a sufficient amount of product to replace the defective product.
View our Stone Restoration Pictures Featuring projects that utilized our many products for their building's restoration, maintenance or cleaning project.
After cleaning or sealing stone surfaces, the glass windows and metal frames almost always need to be cleaned, and many times window spots and stains will need to be removed as well. View our glass and metal products that compliment our stone restoration and protection products.
DON'T FORGET THE GLASS AND METAL SURFACES
View All Products > Architectural Precast, Concrete, Brick & Block Restoration Products > Stone Protection Products >